181 lines
6.9 KiB
Plaintext
181 lines
6.9 KiB
Plaintext
|
|
Section 1 Overview
|
|
|
|
The Media Oriented Systems Transport (MOST) driver gives Linux applications
|
|
access a MOST network: The Automotive Information Backbone and the de-facto
|
|
standard for high-bandwidth automotive multimedia networking.
|
|
|
|
MOST defines the protocol, hardware and software layers necessary to allow
|
|
for the efficient and low-cost transport of control, real-time and packet
|
|
data using a single medium (physical layer). Media currently in use are
|
|
fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
|
also supports various speed grades up to 150 Mbps.
|
|
For more information on MOST, visit the MOST Cooperation website:
|
|
www.mostcooperation.com.
|
|
|
|
Cars continue to evolve into sophisticated consumer electronics platforms,
|
|
increasing the demand for reliable and simple solutions to support audio,
|
|
video and data communications. MOST can be used to connect multiple
|
|
consumer devices via optical or electrical physical layers directly to one
|
|
another or in a network configuration. As a synchronous network, MOST
|
|
provides excellent Quality of Service and seamless connectivity for
|
|
audio/video streaming. Therefore, the driver perfectly fits to the mission
|
|
of Automotive Grade Linux to create open source software solutions for
|
|
automotive applications.
|
|
|
|
The driver consists basically of three layers. The hardware layer, the
|
|
core layer and the application layer. The core layer consists of the core
|
|
module only. This module handles the communication flow through all three
|
|
layers, the configuration of the driver, the configuration interface
|
|
representation in sysfs, and the buffer management.
|
|
For each of the other two layers a selection of modules is provided. These
|
|
modules can arbitrarily be combined to meet the needs of the desired
|
|
system architecture. A module of the hardware layer is referred to as an
|
|
HDM (hardware dependent module). Each module of this layer handles exactly
|
|
one of the peripheral interfaces of a network interface controller (e.g.
|
|
USB, MediaLB, I2C). A module of the application layer is referred to as an
|
|
AIM (application interfacing module). The modules of this layer give access
|
|
to MOST via one the following ways: character devices, ALSA, Networking or
|
|
V4L2.
|
|
|
|
To physically access MOST, an Intelligent Network Interface Controller
|
|
(INIC) is needed. For more information on available controllers visit:
|
|
www.microchip.com
|
|
|
|
|
|
|
|
Section 1.1 Hardware Layer
|
|
|
|
The hardware layer contains so called hardware dependent modules (HDM). For each
|
|
peripheral interface the hardware supports the driver has a suitable module
|
|
that handles the interface.
|
|
|
|
The HDMs encapsulate the peripheral interface specific knowledge of the driver
|
|
and provides an easy way of extending the number of supported interfaces.
|
|
Currently the following HDMs are available:
|
|
|
|
1) MediaLB (DIM2)
|
|
Host wants to communicate with hardware via MediaLB.
|
|
|
|
2) I2C
|
|
Host wants to communicate with the hardware via I2C.
|
|
|
|
3) USB
|
|
Host wants to communicate with the hardware via USB.
|
|
|
|
|
|
Section 1.2 Core Layer
|
|
|
|
The core layer contains the mostcore module only, which processes the driver
|
|
configuration via sysfs, buffer management and data forwarding.
|
|
|
|
|
|
|
|
Section 1.2 Application Layer
|
|
|
|
The application layer contains so called application interfacing modules (AIM).
|
|
Depending on how the driver should interface to the application, one or more
|
|
suitable modules can be selected.
|
|
|
|
The AIMs encapsulate the application interface specific knowledge of the driver
|
|
and provides access to user space or other kernel subsystems.
|
|
Currently the following AIMs are available
|
|
|
|
1) Character Device
|
|
Applications can access the driver by means of character devices.
|
|
|
|
2) Networking
|
|
Standard networking applications (e.g. iperf) can by used to access
|
|
the driver via the networking subsystem.
|
|
|
|
3) Video4Linux (v4l2)
|
|
Standard video applications (e.g. VLC) can by used to access the
|
|
driver via the V4L subsystem.
|
|
|
|
4) Advanced Linux Sound Architecture (ALSA)
|
|
Standard sound applications (e.g. aplay, arecord, audacity) can by
|
|
used to access the driver via the ALSA subsystem.
|
|
|
|
|
|
|
|
Section 2 Configuration
|
|
|
|
See ABI/sysfs-class-most.txt
|
|
|
|
|
|
|
|
Section 3 USB Padding
|
|
|
|
When transceiving synchronous or isochronous data, the number of packets per USB
|
|
transaction and the sub-buffer size need to be configured. These values
|
|
are needed for the driver to process buffer padding, as expected by hardware,
|
|
which is for performance optimization purposes of the USB transmission.
|
|
|
|
When transmitting synchronous data the allocated channel width needs to be
|
|
written to 'set_subbuffer_size'. Additionally, the number of MOST frames that
|
|
should travel to the host within one USB transaction need to be written to
|
|
'packets_per_xact'.
|
|
|
|
Internally the synchronous threshold is calculated as follows:
|
|
|
|
frame_size = set_subbuffer_size * packets_per_xact
|
|
|
|
In case 'packets_per_xact' is set to 0xFF the maximum number of packets,
|
|
allocated within one MOST frame, is calculated that fit into _one_ 512 byte
|
|
USB full packet.
|
|
|
|
frame_size = floor(MTU_USB / bandwidth_sync) * bandwidth_sync
|
|
|
|
This frame_size is the number of synchronous data within an USB transaction,
|
|
which renders MTU_USB - frame_size bytes for padding.
|
|
|
|
When transmitting isochronous AVP data the desired packet size needs to be
|
|
written to 'set_subbuffer_size' and hardware will always expect two isochronous
|
|
packets within one USB transaction. This renders
|
|
|
|
MTU_USB - (2 * set_subbuffer_size)
|
|
|
|
bytes for padding.
|
|
|
|
Note that at least 2 times set_subbuffer_size bytes for isochronous data or
|
|
set_subbuffer_size times packts_per_xact bytes for synchronous data need to be
|
|
put in the transmission buffer and passed to the driver.
|
|
|
|
Since HDMs are allowed to change a chosen configuration to best fit its
|
|
constraints, it is recommended to always double check the configuration and read
|
|
back the previously written files.
|
|
|
|
|
|
|
|
Section 4 Routing Channels
|
|
|
|
To connect a channel that has been configured as outlined above to an AIM and
|
|
make it accessible to user space applications, the attribute file 'add_link' is
|
|
used. To actually bind a channel to the AIM a string needs to be written to the
|
|
file that complies with the following syntax:
|
|
|
|
"most_device:channel_name:link_name[.param]"
|
|
|
|
The example above links the channel "channel_name" of the device "most_device"
|
|
to the AIM. In case the AIM interfaces the VFS this would also create a device
|
|
node "link_name" in the /dev directory. The parameter "param" is an AIM dependent
|
|
string, which can be omitted in case the used AIM does not make any use of it.
|
|
|
|
Cdev AIM example:
|
|
$ echo "mdev0:ep_81:my_rx_channel" >add_link
|
|
$ echo "mdev0:ep_81" >add_link
|
|
|
|
|
|
Sound/ALSA AIM example:
|
|
|
|
The sound/ALSA AIM needs an additional parameter to determine the audio resolution
|
|
that is going to be used. The following strings can be used:
|
|
|
|
- "1x8" (Mono)
|
|
- "2x16" (16-bit stereo)
|
|
- "2x24" (24-bit stereo)
|
|
- "2x32" (32-bit stereo)
|
|
|
|
$ echo "mdev0:ep_81:audio_rx.2x16" >add_link
|
|
$ echo "mdev0:ep_81" >add_link
|